Top

  1. Previous
    Next
    Product 1 of 33
    This product was added to our catalog on Saturday 22 December, 2012.

    .Aqua Flo HIgh-Head and Medium-Head Dominator Pump Diagrams

    Price:  

    Aqua Flo Dominator Pump Diagram

    PRIMING PUMP

    At initial start-up, pump must be primed by filling hair and lint trap with water. To prime pump, remove cover from hair and lint trap: fill pump and suction trap with water. Replace cover (make sure the O-ring is in place) and tighten lock ring. Pump will now prime, with priming time depending upon lift and horizontal distance of suction piping.

    • CAUTION: Do not remove hair and lint strainer lid while pump is running or under pressure! Lid is held in place by a lock ring which can be removed or tightened by hand. Basket must be kept clear of leaves and debris at all times.

    REMOVING BASKET

    1. Turn off motor.
    2. Remove lock ring by rotating counter clockwise.
      DO NOT USE TOOLS.
    3. Remove lid.
    4. Remove basket and empty debris.
    5. Replace basket, fill with water, replace lid and lock ring securely to prevent air from entering and tighten.
      DO NOT USE TOOLS.
    6. Turn on motor
    7. Open air-relief valve on top of filter until steady stream of water comes out.

    NOTE: If pump is installed below water level of pool, close return and suction lines prior to opening hair and lint pot. Make sure to re-open valves prior to operating.
    DO NOT RUN PUMP DRY!
    Always maintain proper water level in pool. If water level falls below skimmer intake, pump will suck air. Pump is equipped with a maintenance-free, heavy-duty mechanical seal. Damage will occur if pump runs dry, and warranty will be voided.

    TO PREVENT FREEZING

    Drain liquid from pump through plug at bottom front section of volute. It is recommended to apply a good rust inhibitor into liquid end to prevent corrosion. Be sure motor is kept dry and covered. In mild climate area, when freezing may occur, run pump and filter equipment continuously to prevent freezing.

     

    1 B121 Motor "C" Face 3/4 HP Medium Head medium-head dominator motor aqua-flo a.o. smith
    B120 Motor "C" Face 1/2 HP Medium Head medium-head dominator motor aqua-flo a.o. smith
    B122 Motor "C" Face 1 HP Medium Head medium-head dominator motor aqua-flo a.o. smith
    B123 Motor "C" Face 1 1/2HP Medium Head medium-head dominator motor aqua-flo a.o. smith
    B124 Motor "C" Face 2 HP Medium Head medium-head dominator motor aqua-flo a.o. smith
    B125 Motor "C" Face 3 HP Medium Head medium-head dominator motor aqua-flo a.o. smith
    2 B846 Motor Square Flange 2 HP High Head high-head dominator motor aqua-flo a.o. smith
    B847 Motor Square Flange 2 HP High Head high-head dominator motor aqua-flo a.o. smith
    B848 Motor Square Flange 2 HP High Head high-head dominator motor aqua-flo a.o. smith
    B849 Motor Square Flange 2 HP High Head high-head dominator motor aqua-flo a.o. smith
    B748 Motor Square Flange 2 HP High Head high-head dominator motor aqua-flo a.o. smith
    3 99050250 Bolt, Hex Machine, 3/8"-16 x 1"  
    4 99050300 Bolt, Hex Machine, 3/8"-16 x 1-1/2  
    5 99890000 Washer, Flat 3/8"  
    6 91100150 Base  
    7 92280003 Plate, Seal, PS-“200 Seal aqua-flo dominator pump seal plate
    8 91140351 Bracket, PS-“200” Seal aqua-flo dominator pump bracket
    9 92500150 Seal Replacement PS-“200” Seal,
    On models prior to 1995 use PS-1000 seal
     
    10 91692450 V40-416 Impeller, 0.75 HP, High Head aqua-flo dominator pump impeller high-head
    91692500 V40-417 Impeller, 1.0 HP, High Head aqua-flo dominator pump impeller high-head
    91692550 V40-418 Impeller, 1.5 HP, High Head aqua-flo dominator pump impeller high-head
    91692600 V40-419 Impeller, 2.0 HP, High Head aqua-flo dominator pump impeller high-head
    11 91692455 V40-411 Impeller, 0.75 HP, Medium Head aqua-flo dominator pump impeller medium-head
    91692505 V40-412 Impeller, 1.0 HP, Medium Head aqua-flo dominator pump impeller medium-head
    91692555 V40-413 Impeller, 1.5 HP, Medium Head aqua-flo dominator pump impeller medium-head
    91692605 V40-414 Impeller, 2.0 HP, Medium Head aqua-flo dominator pump impeller medium-head
    12 99730150 V26-352 Screw, 1/4"-20 x 11/16" aqua-flo dominator pump l-t bolt
    13 99730160 Screw, 1/4"-20 x 1/2", LH, RD, HD  
    14 92520040 Shaft, Extension, “200” Seal  
    15 99730000 Screw, Socket Set 1/4" - 20 x 5/16"  
    16 91270002 V40-415 Diffuser High-Head aqua-flo dominator pump seal high head diffuser
    17 56910070 Diffuser Assembly  
    17A 91270020 Diffuser Medium-Head aqua-flo dominator pump seal medium head diffuser
    17B 92830051 Wear Ring  
    18 92200140 O-ring, Metric  
    19 92200250 O-ring, #232  
    19A 92200100 O-ring, #229  
    20 99730060 Screw, 8/32" x 3/4" Phillips Pan Head  
    21 99730550 Screw, 8/32" x 1" Phillips Pan Head  
    22 92200180 O-ring, #449 aqua-flo dominator pump seal plate o-ring
    23 99100020 Clamp, V, “D” Series, with knob  
    24 91200003 V40-900 Casing, “D” Series, Volute aqua-flo dominator pump volute val-pak v40-900
    25 92200060 O-ring, #111  
    26 92290020 Plug, Pipe, Wing  
    27 91920050 Lock Ring, Trap  
    28 91230300 V40-430 Cover, Trap aqua-flo dominator pump lid clear lid v40-430 val-pak
    29 92200190 O-ring, Trap Lid, #254  
    30 91110040 Basket, Strainer, 6", “D” Series aqua-flo dominator pump basket val-pak
    31 92620552 Trap, 6" x 2" aqua-flo dominator pump pot trap
    32 91450210 Flange, Suction 2"  
    33 99050000 Bolt, Hex Machine, 3/8" - 16 x 3/4"  
    34 52203000 Fitting, Compression Comp., 2" x 1-1/2"  
    52202000 Fitting, Compression Comp., 2" x 2"  
    35 92200210 O-ring, #230  
    36 91431250 Fitting, Tail Piece, 2" x 1-1/2"  
    91431200 Fitting, Tail Piece, 2"  
    37 91431150 Fitting, Union Nut, 2"  
    Reviews

Categories

Brands

Share Product

Share via E-Mail Share on Facebook Share on Twitter Share on Google Buzz Share on Digg

Manufacturer Info