Aqua Flo A Series Pump Diagram

PRIMING PUMP

At initial start-up, pump must be primed by filling hair and lint trap with water. To prime pump, remove cover from hair and lint trap: fill pump and suction trap with water. Replace cover (make sure the o-ring is in place) and tighten lock handles. Pump will now prime, with priming time depending upon lift and horizontal distance of suction piping.

• CAUTION: Do not remove hair and lint strainer lid while pump is running or under pressure! Lid is held in place by lock handles which can be removed or tightened by hand. Basket must be kept clear of leaves and debris at all times.

REMOVING BASKET

1. Turn off motor.
2. Remove lid.
3. Remove basket and empty debris.
4. Replace basket, fill with water, replace lid securely to prevent air from entering and tighten. DO NOT USE TOOLS.
5. Turn on motor.
6. Open air-relief valve on top of filter until steady stream of water comes out.

NOTE: If pump is installed below water level of pool, close return and suction lines prior to opening hair and lint pot. Make sure to re-open valves prior to operating.

DO NOT RUN PUMP DRY!
Always maintain proper water level in pool. If water level falls below skimmer intake, pump will suck air. Pump is equipped with a maintenance-free, heavy-duty mechanical seal. Damage will occur if pump runs dry, and warranty will be voided.

TO PREVENT FREEZING
Drain liquid from pump through plug at bottom section of volute. It is recommended to apply a good rust inhibitor into liquid end to prevent corrosion.

Be sure motor is kept dry and covered. In mild climate area, when freezing may occur, run pump and filter equipment continuously to prevent freezing.

1	B121	MOTOR 3/4 HP
	B120	MOTOR 1/2 HP
	B122	MOTOR 1 HP
	B123	MOTOR 1 1/2HP
	B124	MOTOR 2 HP
	B125	MOTOR 3 HP
2	92520000 V40-116	SHAFT EXTENSION
3	99730000 V40-401	SCREW, SOCKET SET, 1/4”-20 X 5/16”
4	91140050 V40-460	BRACKET, 1/3-3 HORSEPOWER
	91140100 V30-461	BRACKET, 1/3-3 HORSEPOWER WITH FOOT
5	99050030	BOLT, HEX MACHINE, 5/16”-18 X 5/8”
6	99050050	BOLT, HEX MACHINE, 3/8”-16 X 5/8”
7	91500059 G44 V40-115	VOLUTE GASKET
8	92509040 PS-1000	SHAFT SEAL
9	91691000 V40-452	IMPELLER 0.33 HP
	91691052 V40-453	IMPELLER 0.5 HP
	91691101 V40-454	IMPELLER 0.75 HP
	91691201 V40-455	IMPELLER 1.0 HP
	91691151 V40-456	IMPELLER 1.5 HP
	91691251 V40-457	IMPELLER 2.0 HP
	91691300 V40-458	IMPELLER 3.0 HP
10	92770200	Volute 0.33-2.0 HP, 100% Drain
10	92770060	VOLUTE 0.33-2.0 HP
11	91100100	PLASTIC BASE
12	99050110	BOLT, HEX MACHINE, 5/16”-18 X 1”
13	99890050	WA
14	92290000	PIPE PLUG
15	91500150 V40-118 G57	GASKET, TRAP, 5”
	91500200	GASKET, TRAP, 6” AND 8”
16	92620000	TRAP, 5”, 1-1/2” SUCTION
17	91110000 B-33 V40-465	BASKET, STRAINER, 5”
	91110010	BASKET, STRAINER, 6”
18	92200000	O-RING, TRAP COVER, 5”
	92200010	O-RING, TRAP COVER, 6”
19	91230000 V40-463	TRAP COVER, 5”
	91230050	TRAP COVER, 6”
20	91920001 V40-468	LOCKHANDLE