Aqua Flo Dominator Pump Diagram

PRIMING PUMP

At initial start-up, pump must be primed by filling hair and lint trap with water. To prime pump, remove cover from hair and lint trap: fill pump and suction trap with water. Replace cover (make sure the O-ring is in place) and tighten lock ring. Pump will now prime, with priming time depending upon lift and horizontal distance of suction piping.

• CAUTION: Do not remove hair and lint strainer lid while pump is running or under pressure! Lid is held in place by a lock ring which can be removed or tightened by hand. Basket must be kept clear of leaves and debris at all times.

REMOVING BASKET

1. Turn off motor.
2. Remove lock ring by rotating counter clockwise.
   DO NOT USE TOOLS.
3. Remove lid.
4. Remove basket and empty debris.
5. Replace basket, fill with water, replace lid and lock ring securely to prevent air from entering and tighten.
   DO NOT USE TOOLS.
6. Turn on motor
7. Open air-relief valve on top of filter until steady stream of water comes out.

NOTE: If pump is installed below water level of pool, close return and suction lines prior to opening hair and lint pot. Make sure to re-open valves prior to operating.
DO NOT RUN PUMP DRY!
Always maintain proper water level in pool. If water level falls below skimmer intake, pump will suck air. Pump is equipped with a maintenance-free, heavy-duty mechanical seal. Damage will occur if pump runs dry, and warranty will be voided.

TO PREVENT FREEZING

Drain liquid from pump through plug at bottom front section of volute. It is recommended to apply a good rust inhibitor into liquid end to prevent corrosion. Be sure motor is kept dry and covered. In mild climate area, when freezing may occur, run pump and filter equipment continuously to prevent freezing.

1	B121	Motor "C" Face 3/4 HP Medium Head
	B120	Motor "C" Face 1/2 HP Medium Head
	B122	Motor "C" Face 1 HP Medium Head
	B123	Motor "C" Face 1 1/2HP Medium Head
	B124	Motor "C" Face 2 HP Medium Head
	B125	Motor "C" Face 3 HP Medium Head
2	B846	Motor Square Flange 2 HP High Head
	B847	Motor Square Flange 2 HP High Head
	B848	Motor Square Flange 2 HP High Head
	B849	Motor Square Flange 2 HP High Head
	B748	Motor Square Flange 2 HP High Head
3	99050250	Bolt, Hex Machine, 3/8"-16 x 1"
4	99050300	Bolt, Hex Machine, 3/8"-16 x 1-1/2
5	99890000	Washer, Flat 3/8"
6	91100150	Base
7	92280003	Plate, Seal, PS-“200 Seal
8	91140351	Bracket, PS-“200” Seal
9	92500150	Seal Replacement PS-“200” Seal, On models prior to 1995 use PS-1000 seal
10	91692450 V40-416	Impeller, 0.75 HP, High Head
	91692500 V40-417	Impeller, 1.0 HP, High Head
	91692550 V40-418	Impeller, 1.5 HP, High Head
	91692600 V40-419	Impeller, 2.0 HP, High Head
11	91692455 V40-411	Impeller, 0.75 HP, Medium Head
	91692505 V40-412	Impeller, 1.0 HP, Medium Head
	91692555 V40-413	Impeller, 1.5 HP, Medium Head
	91692605 V40-414	Impeller, 2.0 HP, Medium Head
12	99730150 V26-352	Screw, 1/4"-20 x 11/16"
13	99730160	Screw, 1/4"-20 x 1/2", LH, RD, HD
14	92520040	Shaft, Extension, “200” Seal
15	99730000	Screw, Socket Set 1/4" - 20 x 5/16"
16	91270002 V40-415	Diffuser High-Head
17	56910070	Diffuser Assembly
17A	91270020	Diffuser Medium-Head
17B	92830051	Wear Ring
18	92200140	O-ring, Metric
19	92200250	O-ring, #232
19A	92200100	O-ring, #229
20	99730060	Screw, 8/32" x 3/4" Phillips Pan Head
21	99730550	Screw, 8/32" x 1" Phillips Pan Head
22	92200180	O-ring, #449
23	99100020	Clamp, V, “D” Series, with knob
24	91200003 V40-900	Casing, “D” Series, Volute
25	92200060	O-ring, #111
26	92290020	Plug, Pipe, Wing
27	91920050	Lock Ring, Trap
28	91230300 V40-430	Cover, Trap
29	92200190	O-ring, Trap Lid, #254
30	91110040	Basket, Strainer, 6", “D” Series
31	92620552	Trap, 6" x 2"
32	91450210	Flange, Suction 2"
33	99050000	Bolt, Hex Machine, 3/8" - 16 x 3/4"
34	52203000	Fitting, Compression Comp., 2" x 1-1/2"
	52202000	Fitting, Compression Comp., 2" x 2"
35	92200210	O-ring, #230
36	91431250	Fitting, Tail Piece, 2" x 1-1/2"
	91431200	Fitting, Tail Piece, 2"
37	91431150	Fitting, Union Nut, 2"